Need Help?

2000 Hyundai Elantra GLS 4dr Sedan Manual

2000 Hyundai Elantra
Trim Info:
Front Wheel Drive, 4 Door Sedan, Compact
24 mpg city / 33 mpg hwy
Other Trims
Do you own this car?
Estimated Mileage
 Miles
Enter current mileage for most
accurate info about this vehicle


Track Your Service Records
Get Recall Alerts
Get Updated Value Estimates on Your Car.

back to question list

Ask the Community

Ask Our Auto Mechanics


November 4, 2012, 11:40 am

Scott L
 

Question: 2000 Hyundai elantra fuel pump

My fuel pump doesn't seem to kick on. Car ran fine, stalled and won't start now. It does turn over but no start. Replaced relay and same problem. Took out pump and ran constant 12v to pump. It does work.


November 9, 2012, 5:02 pm

Ron W
Expert Mechanic

Check your crank position sensor.

It sends out the RPM signal to the PCM. If it is bad, there is no RPM signal, and the PCM will not command the injectors to fire. Easiest way to see if it works is to hook up a scantool and crank the engine. Monitor the datastream for RPM. If you see RPM then the sensor is working, if it reads zero RPM, then there is a problem with the Crank Position Sensor circuit.

If you don't have a scantool, you could just replace it and see what happens. Most are under $30.


1/1 users found this helpful.

November 9, 2012, 5:16 pm

Scott L
 

Ok i know how to check that with a multi meter. My fuel pump wrong come on with the key but will if i run a wire from the positive side of the battery too the fuel pump. I replaced the relay and there is no fuse or cut off switch for the fuel pump to my knowledge. Would the crank sensor cause that as well?


0/0 users found this helpful.

November 9, 2012, 5:48 pm

Ron W
Expert Mechanic

Will the car run with the fuel pump powered up directly? If it will, the crank position sensor is probably OK. It kills the injectors on most vehicles. I wold see if there is power getting to the rely with the car cranking. If not, you have an ignition feed issue. If i does, then it probably is a wiring issue between the relay and the pump.


0/0 users found this helpful.

November 9, 2012, 6:00 pm

Scott L
 

No it won't start with the pump going. I get what your saying and I'll check the crank sensor tomorrow. But for the fuel pump, is there an easy way to find out if the problem is in the ignition or the wiring between the relay and pump?


0/0 users found this helpful.

November 9, 2012, 9:09 pm

Ron W
Expert Mechanic

Testing at the relay is the first step. Make sure there is battery voltage at one terminal and an ignition feed when cranking, That breaks the circuit in two.

If it's good, check power at the pump. If there isn't power start tracing back.

If the ignition feed is bad, check the output voltage at the ignition switch. and work toward the relay from there.

If the battery feed is bad, check the fuse that feeds the circuit and work from there.

One other quick thing you can do is put a fused jumper across the fuel pump Bat feed circuit to the wire that goes to the pump. If the pump runs, then the wiring to the pump (and the pump) are most likely OK.


0/0 users found this helpful.

1 2 
Ask our panel of certified auto mechanics a question. We pay for their advice so you don't have to



My Auto Score

See the free AutoCheck score

Meet The Experts
Kim Perrin
Kim Perrin is our resident mechanic here at DriverSide. Kim worked as…
Tyler Orr
Tyler Orr is an expert in German and Japanese cars and has been a mechanic …
Elizabeth Kriesten
Elizabeth Kriesten worked as an automotive technician for several years at Dodge…
Tips on Servicing

Car Brakes: How Do You Know When to Change Them?

By Zach Bowman For those who suffer a daily commute through heavy traffic, your vehicle's braking system can bring thousands of pounds of metal, plastic and empty Starbucks cups to a stop hundreds of times before you get to work. It goes without saying that these pieces wear out, but they do so slowly, meaning you may not notice they need attention until ...

Read more…