Need Help?

1996 GMC Sierra 1500 Base Reg Cab 117.5 WB

1996 GMC Sierra 1500
Trim Info:
Rear Wheel Drive, Reg Cab 6.5' Wideside
17 mpg city / 22 mpg hwy
Other Trims
Do you own this car?
Estimated Mileage
 Miles
Enter current mileage for most
accurate info about this vehicle


Track Your Service Records
Get Recall Alerts
Get Updated Value Estimates on Your Car.

back to question list

Ask the Community

Ask Our Auto Mechanics


June 11, 2013, 10:07 am

Dwayne G
 

Question: 96 GMC Sierra 5.7l Vortec - no power in gear

Hi guys, first time I've ever tried coming online to ask someone because I'm completely stumped.

Disclaimer: I am NOT a mechanic, have just figured it out by ear my whole life.

My vehicle: 1996 GMC Sierra 1500 2WD Auto w/ 5.7l Vortec

Beginning: Just bought the truck for next to nothing with bad engine. Replaced engine 1 month ago with identical engine with "140k" miles on it. (Who really knows right... it looked and ran great for last month.) My buddy and I split the work and turned it into a few hour process. In doing so, we somehow managed to completely miss plugging the map sensor back in this whole month.

Middle: The truck ran strong, minus a very quick and sudden complete stall, if you stepped your foot in the gas. The stall actually felt like the truck just "died" for about 1 second, then VROOOM. The truck also smelled like it was burning lean, but I never had time to tinker with it.

About 2 weeks ago, I started to notice that the truck would run kind of rough and vibrate/shake any time you were "coasting" down the road and barely had to touch the gas petal to remain at 30mph/45mph/55mph for city speed limits. It also felt like the truck would shift too early and sort of bog down.

Today, I drove the truck for about 10 miles and on the way home, I noticed that the truck would do that "pipe pop" like a manual transmission when you rack up the rpms and let off the gas. (I have dual exhaust from manifolds to 2 flowmaster mufflers and echo tips, no cats). Anyway, normally, if I was going 45mph in 3rd gear, and let off the gas, it would seem like it went into "neutral" and quietened down. Today, it was doing the "pop pop pop BOOM pop pop" sound. It actually backfired a few times. When I noticed it do it by itself, I got curious and actually put it into 2nd manually, to see if it would do it again. It did. I NEVER abused it and the RPMs never went over 2.5k in the process... I think it redlines at 6 or 7...

After I got it home, didn't think anything about it, because it was cold this morning, cold start, left quick..

Ending: Later, I took the truck again, but made it about 8 miles before I just lost all power. I was on the interstate, attempting to reach 75mph and keep up with traffic when it just progressively lost power. By the time 5 more miles were up, I was on the interstate going 50mph with my foot almost in the floor. So I let off the gas and putted to the nearest exit, where I parked it at an autozone.

I had autozone do a diagnostic scan, and it said MAF and MAP sensor. (This is how I found out the map sensor had never been plugged back in)

The truck would start, idle poorly, then eventually adjust up to being able to idle fairly... but the moment I put it in gear, it just bogs down and loses all power.

I have another vehicle (98 z71 w/ same motor) so I changed the MAP sensor, the MAF sensor, the idle air sensor and throttle position sensor with the other vehicle and no difference other than idling more poorly with different configurations of swapping parts. (I did not do battery reset between sensor testing). I tried changing the entire breather and no difference. I had recently replaced the fuel sending unit and the guys that did my exhaust removed my cats and wouldn't let me keep them......

I have not tried crank sensor, cam pos sensor or anti-knock sensor.

Tonight after dark, I went back out to the truck to tinker and noticed that I got a neat little display show from 4 plug wires AND my coil wire going to distributor. The second and last plugs (from front) on BOTH sides, were jumping. Not a strong jump, just enough to show a fuzzy blue light show. The connection at the coil was doing the same thing. So #4, #8, #3, #7 and coil. Everything was closed, so I couldn't change plugs and wires yet.

So right now, my truck idles at almost correct state, but vibrates. The moment I attempt to put it in gear, it bogs way down and tries to die, and shakes horribly. If I try to drive, I have no power. With pedal 1/2 way down, I would hit 30 mph in about 4 minutes...

Could it just be the plugs/wires? Is it something more serious? Until I noticed the sparks, I was going to try fuel filter next. Or thinking I got water-gas...

Any ideas on what to try next? Sorry for the long post, just trying to be thorough in the explanation.


June 11, 2013, 5:11 pm

Richard W
Expert Mechanic

If you have any blue little spark around the plugs or coil you have to fix that. SO I would replace the wires cap and rotor first. Before I did that I would check the fuel pressure. It needs to be 55psi to make the car run. Also it need to have the right amount of fuel getting to the engine. The most common problem with your truck is the fuel pump. But if you can't check the fuel pump you need to fix the little blue spark and recheck your problem.


0/0 users found this helpful.

June 11, 2013, 7:27 pm

Dwayne G
 

UPDATE:

Replaced spark plugs/wires and tested each for adequate spark and found something strange. We were able to remove ALL spark plug wires from the passenger side and there was no difference in how the engine ran. So #2 - #8 cylinders are not working. Where would I even begin?


0/0 users found this helpful.

June 11, 2013, 8:19 pm

Dwayne G
 

I forgot to say that the plugs and wires were replaced and they are all getting spark just fine... just not "firing". When plugs are taken out, they are a little wet, but not soaked or anything...


0/0 users found this helpful.

Ask our panel of certified auto mechanics a question. We pay for their advice so you don't have to



My Auto Score

See the free AutoCheck score

Meet The Experts
Kim Perrin
Kim Perrin is our resident mechanic here at DriverSide. Kim worked as…
Tyler Orr
Tyler Orr is an expert in German and Japanese cars and has been a mechanic …
Elizabeth Kriesten
Elizabeth Kriesten worked as an automotive technician for several years at Dodge…
Tips on Servicing

Car Brakes: How Do You Know When to Change Them?

By Zach Bowman For those who suffer a daily commute through heavy traffic, your vehicle's braking system can bring thousands of pounds of metal, plastic and empty Starbucks cups to a stop hundreds of times before you get to work. It goes without saying that these pieces wear out, but they do so slowly, meaning you may not notice they need attention until ...

Read more…