Need Help?

1993 Chevrolet Lumina Base 4dr Sedan

1993 Chevrolet Lumina
Do you own this car?
Estimated Mileage
 Miles
Enter current mileage for most
accurate info about this vehicle


Track Your Service Records
Get Recall Alerts
Get Updated Value Estimates on Your Car.

Ask the Community

Ask Our Auto Mechanics

Ask our panel of certified mechanics a question. We pay for their advice so you don't have to.

Enter a Question:
Details:
Which Car is This Question About?

Recent Questions

How do I fix it?
The car was running and it died like it was out of gas. You can turn the key over and it just wont start.
Asked by Rachael D April 10, 2012, 12:44 pm 1 reply
why is my car overheating?
Your question for ExpertCarAdvice expertise is as following : "chevy lumina 99 is overheating!! I put a little water in it the 1st time it happened, and it ran okay for a day going...
Asked by Summer B March 17, 2012, 7:08 pm 1 reply
what do i do now
i have a 1998 chevy lumina and i have changed to water pump, theramstat, and radiator cap; but it still over heating. we took the air out of whatever and still overheating. what do...
Asked by Jackie G March 7, 2012, 11:42 am 1 reply
Overheating
I recently had work done on my 1996 lumina. The intake manifold gasket was changed and a tune up. When I got the car it seemed fine then started overheating again (the orginal reas...
Asked by Chris S February 2, 2012, 6:39 pm 1 reply
Timing Cover Gasket
Could I get an estimate on Cost and Time to replace the Timing Cover Gasket? My 1997 Chevy Lumina is leaking coolant slowly from here. Thanks.
Asked by Chris F January 17, 2012, 6:22 pm 1 reply
code 35 1993 chev lum
replaced idle speed motor reset comp,worked ok untill the next day an code 35 came back and running to fast on cold start
Asked by Clark B January 1, 2012, 11:43 pm 1 reply
why is it difficult to start when it is cold.
recently my lumina has been very hard to start in the mornings. it turns over for about 10 to 15 seconds before firing, and once it does start if you apply pressure to the accele...
Asked by AutomotiveForums M December 13, 2011, 12:26 pm 1 reply
How do I access Camshaft Position Sensor
Replacing the Camshaft Sensor looked and sounded like a pretty simple job. I removed the drive belt, removed 3 bolts from power steering pump, and then cussed for the next 30 min...
Asked by Randy J November 12, 2011, 3:50 pm 1 reply
I am not getting fuel into cylinders
new fuel pump & ,filter good pressure at test port, Injectors do not seem to be opening I did have fault for o2 sensor after change it this happened
Asked by AutomotiveForums M September 18, 2011, 2:27 pm 3 replies
no fuel in cylinder
new pump, filter good pressure at test port injectors not pulsing fuses good crank sensor tested at .6 vac and 900ohms batt power good good spark on cylinders 2,4,6 Is there a ...
Asked by AutomotiveForums M September 21, 2011, 5:53 pm 1 reply




My Auto Score

See the free AutoCheck score

Meet The Experts
Kim Perrin
Kim Perrin is our resident mechanic here at DriverSide. Kim worked as…
Tyler Orr
Tyler Orr is an expert in German and Japanese cars and has been a mechanic …
Elizabeth Kriesten
Elizabeth Kriesten worked as an automotive technician for several years at Dodge…
Tips on Servicing

Car Brakes: How Do You Know When to Change Them?

By Zach Bowman For those who suffer a daily commute through heavy traffic, your vehicle's braking system can bring thousands of pounds of metal, plastic and empty Starbucks cups to a stop hundreds of times before you get to work. It goes without saying that these pieces wear out, but they do so slowly, meaning you may not notice they need attention until ...

Read more…