Need Help?

2008 Chrysler Sebring Base 4dr Sedan LX FWD

2008 Chrysler Sebring
Trim Info:
Front Wheel Drive, 4 Door Sedan, Midsize
21 mpg city / 30 mpg hwy
Other Trims
Do you own this car?
Estimated Mileage
 Miles
Enter current mileage for most
accurate info about this vehicle


Track Your Service Records
Get Recall Alerts
Get Updated Value Estimates on Your Car.
back to question list

Ask the Community

Ask Our Auto Mechanics


March 4, 2013, 8:37 pm

Alan W
 

Question: How to remove bolts from timing chain cover

I can't seem to raise or lower the motor enough to remove the bolts used in the timing belt cover and the right motor mount on a 1997 chrysler Sebring 2.0L Coupe. i can't clear the vehicle frame to remove them. i removed the middle motor mount as well but still could not get them to clear the frame.


March 8, 2013, 3:34 pm

Tyler O
Expert Mechanic

REMOVAL

Remove coolant reserve tank.
Remove crankshaft pulley.
Follow removal procedure outlined in illustration, noting the following.

NOTE: Place the removed power steering oil pump in a place where it will not be a hindrance when removing and installing the timing belt, and tie it with a cord.

Remove the power steering oil pump from the bracket with the hose attached.
Place a garage jack against the engine oil pan with a piece of wood in between, jack up the engine so that the weight of the engine is no longer being applied to the engine mount bracket, and then remove the engine mount bracket.

CAUTION: Do not rotate the camshaft or crankshaft after removing the timing belt, or valve components may be damaged. Always align timing marks before removing timing belt.




Align timing marks. Loosen the timing belt tensioner to remove timing belt.
When the tensioner is removed from the engine, it is necessary to compress the plunger into the tensioner body.

NOTE: Index the tensioner in the vise the same way it is installed on the engine. This is to ensure proper pin orientation when the tensioner is installed on the engine.




Place the tensioner into a vise and slowly compress the plunger.
When the plunger is compressed into the tensioner body, install a pin through the body and plunger to retain plunger in place until tensioner is installed.

INSTALLATION

Follow removal procedure in reverse order noting the following.




Set the crankshaft sprocket to TDC by aligning the sprocket with the arrow on the oil pump housing.
Set the camshafts timing marks together by aligning notches on sprockets.
Move the crankshaft to 1/2 notch before TDC.




Install the timing belt. Starting at the crankshaft, go around the water pump sprocket, idler pulley, camshaft sprockets and then around the tensioner pulley.
Move the crankshaft sprocket to TDC to take up belt slack. Install the tensioner to block but do not tighter, fasteners.




Using a torque wrench on the tensioner pulley, apply 28 Nm (21 ft. lbs.) of torque to tensioner.
With torque being applied to the tensioner pulley, move the tensioner up against the tensioner pulley bracket and tighten fasteners to 31 Nm (23 ft. lbs.) .
Pull the tensioner plunger pin. Pretension is correct when the pin can be removed and installed.
Rotate the crankshaft 2 revolutions and check the alignment of the timing marks. If marks are not aligned correctly, do it again.


1/1 users found this helpful.

March 11, 2013, 8:55 pm

Alan W
 

Thanks for your reply Tyler. I appreciate the list of the necessary steps. I would like more resolution on the step that says to remove the engine mount bracket. The bolts are 4 inches long but the distance from the timing belt cover ( or engine mount) to the vehicle frame is only 2 inches or so. I've been trying to lower the engine enough to remove them but have not been successful. Do I need to remove all the engine mounts including the lower engine support strut to get the engine low enough to remove the bolts? I keep thinking there must be an easier way but I can't see it.


0/0 users found this helpful.

Ask our panel of certified auto mechanics a question. We pay for their advice so you don't have to



My Auto Score

See the free AutoCheck score

Meet The Experts
Kim Perrin
Kim Perrin is our resident mechanic here at DriverSide. Kim worked as…
Tyler Orr
Tyler Orr is an expert in German and Japanese cars and has been a mechanic …
Elizabeth Kriesten
Elizabeth Kriesten worked as an automotive technician for several years at Dodge…
Tips on Servicing

Car Brakes: How Do You Know When to Change Them?

By Zach Bowman For those who suffer a daily commute through heavy traffic, your vehicle's braking system can bring thousands of pounds of metal, plastic and empty Starbucks cups to a stop hundreds of times before you get to work. It goes without saying that these pieces wear out, but they do so slowly, meaning you may not notice they need attention until ...

Read more…